GRACO 24A082 - Spring Operated Fluid Regulator, 250 Max psi, 5-100 PSI Range, ISO Pitch Thread, 0-100 PSI Gauge Pressure Range, Fluid housing is coated w/ PTFE based polymer

Specifications

• Thread: ISO pitch thread inlet and outlet (not compatible with US standard pitch)
• Max Working Pressure: 250 PSI (1800 kPa, 18 bar) maximum fluid inlet pressure
• Material: Fluid housing coated with PTFE polymer
• Series: A
• Regulated Pressure Range: 5-100 PSI (34-700 kPa, 0.3-7 bar)
• Gauge Pressure Range: 0-100 PSI (0-700 kPa, 0-7 bar)
• Gauge Included: Yes (see below)
• Certifications: CE and Ex II 2 G certified
• Torque Sequences: 21-25 ft-lb (28-34 N•m), 21-35 ft-lb (28-47 N•m), 23-27 ft-lb (31-36 N•m)
• Assembly Note: PTFE side down toward housing
• Tightening Sequence: Numbers indicate tightening sequence - tighten evenly to 7-10 ft-lb (9-14 N•m), then retorque to 125 in-lb (14 N•m) three times consecutively to compensate for diaphragm relaxation

Compatible Equipment

• Spring Operated Installation systems
• Models 214895 - Low Pressure Fluid Regulator, 250 Max psi, 5-100 PSI Range, 3.0 GPM, SST, Spring Type, 3/8 (F) x 3/8 (F), 1/4 (F) Port
• 26C160 - Fluid Pressure Regulator, Stainless, 250 PSI
• 24A082 - Spring Operated Fluid Regulator, 250 Max psi, 5-100 PSI Range, ISO Pitch Thread, 0-100 PSI Gauge Pressure Range, Fluid housing is coated w/ PTFE based polymer

Related Parts

• 214895 - Low Pressure Fluid Regulator, 250 Max psi, 5-100 PSI Range, 3.0 GPM, SST, Spring Type, 3/8 (F) x 3/8 (F), 1/4 (F) Port
• 214706 - Low Pressure Fluid Regulator, 250 Max psi, 5-100 PSI Range, 3.0 GPM, SST, Spring Type, 3/8 (F) x 3/8 (F), 1/4 (F) Port
• 26C160 - Fluid Pressure Regulator, Stainless, 250 PSI
• 217314 - Low Pressure Fluid Regulator, 250 Max psi, 20-160 PSI Range, 3.0 GP (m), SST, Spring Type, 3/8 (F) x 3/8 (F), 1/4 (F) Port
• 221118 - Fluid Regulator, 250 Max PSI, 20-160 PSI Range, 3.0 GPM, SS, Spring Type, 3/8"(F) x 3/8 (M), 1/4"(F) Port

ISO pitch thread inlet and outlet. Not compatible with US standard pitch. Fluid housing coated with PTFE polymer. The fluid supply system's main line pressures often exceed the pressure range of the gauge supplied with this regulator. Exposing this gauge to excessive pressure can damage the gauge, causing inaccurate readings and the needle will not return to zero. This damage is not covered by the GRACO warranty. This page shows installation diagram for spring operated models including 24A082, but does not provide detailed specifications. The diagram shows the system setup with fluid supply, air filter & regulator, inlet/outlet ball valves, pipe nipples, and back pressure valve components. This model uses the same assembly configuration as models 214895, 214706, and 26C160, as shown in the right diagram. Assembly includes numbered parts 1-40 with specific torque and tightening sequences.

Reference Manuals

• 307212 (Page 3) Fluid Pressure Regulators