GRACO 24N093 - Husky 515 1/2 in NPT PP Pump, PP Center Section, PP Seats, PTFE Balls & PO Diaphragm
Industrial-grade diaphragm pump component featuring polypropylene construction with PTFE balls for chemical resistance and reliable performance in demanding industrial applications
The Husky 515 air-operated double diaphragm pump features a stall-free low pulsation air valve which provides a smooth and rapid changeover.
The bolt through fluid cover design eliminates leaks and makes the Husky safer with higher reliability.
- Center and end porting options.
- No mechanical seals to cause fluid leaks or failures
- Runs quietly at less than 85 dBa with easy-to-use remote muffler capability for even lower noise levels
- Easy-to-service air valve and ball checks
- Operates on as little as 20 PSI (1.4 bar, 0.14 MPa)
- Split manifold option to pump multiple fluids without mixing
- Delivery up to 15 gpm (56.7 lpm)
- Reliable air valve for years of dependable performance
Additional Specifications
- Material: Polypropylene air motor, fluid section, and seats with PTFE balls
- Pump Size: 0.5 in
- Air Motor: Poly
- Fluid Section: Poly
- Seats: Poly
- Pump Type: 515
- Same As: D5291
- Diaphragm Type: overmolded
| Air Exhaust Port Size (in) | 3/8 |
| Air Exhaust Port Thread Gender | Female |
| Air Exhaust Port Thread Type | NPT |
| Air Inlet Size (in) | 1/4 |
| Air Inlet Thread Gender | Female |
| Air Inlet Thread Type | NPT |
| Application | Industrial |
| Ball Material | PTFE |
| Center Section Material | Polypropylene |
| Compatible Material | Antifreeze, Detergents, Resin, Polymers, Motor Oil, Grease & Oil, Hydraulic Fluid, Transmission Fluid, Cutting Oil, Water - Wastewater Treatment, Ink |
| Connection Type | Threaded |
| Diaphragm Material | PTFE Overmold |
| Fluid Inlet Size (in) | 1/2 |
| Fluid Inlet Thread Gender | Female |
| Fluid Inlet Thread Type | NPT |
| Fluid Outlet Size (in) | 1/2 |
| Fluid Outlet Thread Gender | Female |
| Fluid Outlet Thread Type | NPT |
| Fluid Section Material | Polypropylene |
| Manifold Configuration | Center Port |
| Manifold O-Ring Material | PTFE |
| Material | Polypropylene |
| Maximum Air Consumption (SCFM) | 28 |
| Maximum Air Pressure (MPa) | 0.7 |
| Maximum Air Pressure (psi) | 100 |
| Maximum Cycle Rate (CPM) | 400 |
| Maximum Flow Rate (GPM) | 15 |
| Maximum Fluid Pressure (MPa) | 0.7 |
| Maximum Fluid Pressure (psi) | 100 |
| Maximum Operating Temperature (°F) | 150 |
| Maximum Solid Size (in) | 0.09375 |
| Minimum Operating Temperature (°F) | 40 |
| Overall Height (in) | 10.63 |
| Power Source | Air |
| Seat Material | Polypropylene |
| Standards Met | ATEX, CE |
| Type | Pneumatic Diaphragm Pump |
| Weight (lb) | 6.5 |
Features
- PTFE/EPDM overmolded diaphragms for chemical compatibility
- Polypropylene construction for corrosion resistance
- PTFE balls for superior sealing and chemical resistance
- NPT threaded connections for easy installation
- 0.5 inch pump size for moderate flow applications
Applications
- Industrial fluid transfer
- Chemical processing
- Corrosive fluid handling
- General industrial pumping applications
Compatible Equipment
- Husky industrial pump series
- Husky 515
Related Parts
- 24N094
- 24N095
- 24N096
- 24N097
- 24N098
- 26C020
Part of GRACO's industrial pump series with PTFE/EPDM overmolded diaphragms. Temperature range: 40°F to 180°F (4°C to 82°C). Complies to FDA21CFR 177.1550 (PTFE) and FDA21CFR 177.2600 (EPDM) safety standards. Has overmolded diaphragm parts shown in table below (referenced table not visible on this page). Listed under 'Pumps with Overmolded Diaphragms' section.
Reference Manuals
